Skip to content

HV components 1/2: motor, pump, conveyor on LV assemblers

Chain id: hv_components · Tags: Infinite source

Era setup: HV

Plan modules: HV components (on LV assemblers)

Tips: 5

Machines

LV Assembler · 5 s · 30 EU/tLV
Silver Double Cable2 Silver double cable2Electrum Double Wire4 Electrum double wire4Stainless Steel RodStainless rods2Magnetic Steel Rod1 Magnetic steel rod1
up to 32 EU/t
HV Electric Motor
gtceu:lv_assembler
LV Assembler (pump)LV
HV Electric Motor1Oak 1Pump partsStainless fluid pipeSteel screwSteel rotor2 Rubber ringsGold Single CableGold cables1
up to 32 EU/t
HV Electric Pump
gtceu:lv_assembler
LV Assembler · circuit 1 (conveyor)LV
HV Electric Motor2Rubber864 mB liquid rubberGold Single CableGold cables1
up to 32 EU/t
HV Conveyor Module
gtceu:lv_assembler

Flow

How to build

  1. Input drawers first, one per item: silver, gold and stainless steel ingots (stainless from the EBF chain), steel ingots (steel chain), liquid rubber (rubber chain). Every machine below gets a Modular Router or Pipez item pipe with an Item Filter from its drawers and a Robot Arm Keep Exact cap on its output drawer, so nothing floods. — functionalstorage:oak_1, gtceu:silver_ingot, gtceu:gold_ingot, gtceu:stainless_steel_ingot
  2. Electrum: LV Alloy Smelter, 1 gold + 1 silver → 2 electrum. Wiremill A on electrum, ghost circuit 2: 1 ingot → 1 double wire (4 per motor). Wiremill B on silver, circuit 2: silver double wire; Wiremill C on gold, circuit 1: 1 ingot → 2 single wires. — gtceu:lv_alloy_smelter, gtceu:electrum_ingot, gtceu:lv_wiremill, gtceu:electrum_double_wire
  3. Cable assembler (no ghost circuit): silver double wire + 144 mB liquid rubber → silver double cable; a second one for gold single wire + 144 mB rubber → gold single cable. 7 EU/t, 5 s. Each assembler takes one wire type only. Rubber through an input hatch from the rubber drum. — gtceu:lv_assembler, gtceu:silver_double_cable, gtceu:gold_single_cable, gtceu:rubber_bucket
  4. Lathe A on stainless: 1 ingot → 2 rods (harder rods are off in this pack). Lathe B on steel: 1 ingot → 2 steel rods; the Polarizer turns 1 steel rod into 1 magnetic steel rod (one per motor). — gtceu:lv_lathe, gtceu:stainless_steel_rod, gtceu:lv_polarizer, gtceu:magnetic_steel_rod
  5. Motor assembler: 2 silver double cables + 2 stainless rods + 1 magnetic steel rod + 4 electrum double wires → 1 HV motor in 5 s at 30 EU/t (12 a minute). Keep 64 in the drawer: pistons, pumps, conveyors and arms all pull from here. — gtceu:lv_assembler, gtceu:hv_electric_motor
  6. Pump assembler: 1 motor + 1 gold cable + 1 stainless normal fluid pipe + 1 steel screw + 1 steel rotor + 2 rubber rings → 1 HV pump, 5 s. Extruder: 3 stainless ingots → 1 pipe (pipe mold), 4 steel ingots → 1 rotor (rotor mold). Pumps go into the HV distillery, autoclave, fluid solidifier (2), chemical bath, fluid heater, Industrial Barrel (2) and the cracker (2): stock 8. — gtceu:lv_assembler, gtceu:hv_electric_pump, gtceu:stainless_steel_normal_fluid_pipe
  7. Conveyor assembler on ghost circuit 1: 2 motors + 1 gold cable + 864 mB liquid rubber → 1 conveyor, 5 s. Pipe the rubber in through a fluid hatch side of the machine, never mix it with the cable assemblers’ hatch. — gtceu:lv_assembler, gtceu:hv_conveyor_module, gtceu:rubber_bucket

Tips

  • Every HV component recipe in this fork is an assembler recipe of 5 s at 30 EU/t (ComponentRecipes: duration 100 ticks, EUt VA[LV]). An LV assembler runs all of them, no HV power and no cleanroom. That is why the chain stays on LV machines even though the parts are HV. Piston, robot arm, emitter, sensor and field generator are in HV components 2/2.
  • Motors inside: piston 1, pump 1, conveyor 2, robot arm 2 plus its piston = 3. Make the motor line first and biggest, 12 a minute per assembler.
  • Raw cost per motor: 4 silver + 2 gold (2 silver double cables, 4 electrum ingots from 2 gold + 2 silver in the alloy smelter, standard alloy recipe), 1 stainless ingot (2 rods), 1 steel ingot (1 rod becomes magnetic), 288 mB rubber for the two silver cables.
  • Pump uses the MV Extruder: normal fluid pipe = 3 stainless ingots in an extruder with the pipe mold (about 42 EU/t, so MV), steel rotor = 4 steel ingots in an extruder with the rotor mold (64 EU/t, MV). Rings and screws as in the LV pump line (rubber ring from rubber ingot, screw from lathe on bolts).
  • Cables: 1 wire + 144 mB rubber in an assembler gives 1 cable (single and double alike; 7 EU/t). Gold wire: wiremill circuit 1, 1 ingot → 2 wires. Double wire: circuit 2, 1 ingot → 1. Quadruple would be circuit 4.

Bill of materials

Item Qty
gtceu:lv_assembler 3
gtceu:lv_lathe 2
gtceu:lv_polarizer 1
gtceu:lv_wiremill 3
gtceu:lv_alloy_smelter 1
gtceu:mv_extruder 1
functionalstorage:oak_1 10
modularrouters:modular_router 4
gtceu:lv_robot_arm 6
gtceu:item_filter 6
pipez:item_pipe 16
pipez:fluid_pipe 4

Needs / Feeds